Home Improvement Ideas Decks Deck Building How to Cut and Set Deck Posts for a Solid Frame To build your own deck, follow our step-by-step guide to cutting and setting deck posts that will be the frame for your new favorite hangout. By Caitlin Sole Caitlin Sole Caitlin Sole is the senior home editor at BHG. She is a writer and editor with nearly a decade of interior design expertise. She has vast experience with digital media, including SEO, photo shoot production, video production, eCommerce content, print collaboration, and custom sales content. Learn about BHG's Editorial Process Updated on October 13, 2022 Trending Videos Close this video player Photo: Peter Krumhardt Project Overview Working Time: 10 hours Total Time: 3 days Skill Level: Intermediate Setting the posts for your deck requires careful work, but it can also be exciting because the posts are the first visible sign that your new deck is going up. Although you still have a lot of work to do after you set deck posts, getting them up can make you feel like you're halfway there. Deck posts must be plumb, so they must start with square ends. Check the bottom of each post with a speed square and cut it if necessary. Dip cut ends in a preservative before setting them in the anchors and let the preservative soak in overnight. To make the job go quickly, do everything in stages—first, square all the deck posts and set them in the anchors with a temporary brace. Next, plumb, align, and brace all of them, letting their height run wild before marking and cutting them to a consistent height. Setting deck posts will go more than twice as fast if you have someone help you. Two helpers are even better; you won't have to move back and forth from one post to another to adjust them. Follow along with our steps for setting and cutting deck posts to get started on your backyard makeover. What You'll Need Equipment / Tools Speed square Carpenter's pencil Miter saw or circular saw Framing hammer Post level Mason's line Clamps Wrench Drill Water level Measuring tape Reciprocating saw Materials Lumber Wood preservative Deck post anchor Nails 1x4 boards Fasteners Masking tape Instructions Larry Johnston Square and Preserve Ends of Deck Posts The day before you set the posts, make sure their ends are square. Mark the cut lines with a speed square and make the cuts with a miter saw or circular saw. Dip the cut ends in wood preservative and let them sit overnight. Larry Johnston Set Deck Posts Set each deck post in its anchor. While someone holds it plumb, drive one nail through the anchor hole and about halfway into the post. This will keep the bottom in place but allow you to move it when you plumb it. Tack 1x4 bracing to the post and stake in position. Larry Johnston Brace and Plumb Deck Posts When you've set and temporarily braced all the deck posts, restring the mason's lines on the marks that represent the outside edge of the posts. Clamp a second 1x4 brace to the post and stake it. Plumb each deck post with a post level, keeping its outside face against the mason's line. Larry Johnston Align Deck Posts Recheck the post alignment by sighting down the mason's line. Replumb any post that looks out of line and adjust the bottom of the post if necessary. If you have a post that's plumb but slightly bowed (no more than 1/8 inch), you can force it into place when you install the beams or joists. Project tip: Adjustable post anchors are made to be moved up to the last minute. To adjust, insert an open-end wrench in the slot and loosen the nut just slightly. Tap the post into place with a hammer and a piece of 2x4 scrap, and retighten the nut. Larry Johnston Anchor Deck Posts Drive the remaining fasteners into the post anchor. Some anchors are made to accept nails or screws only. Others are fabricated to accept a lag screw, also. Predrill for the lag screw before driving it. Larry Johnston Mark Level Line Use a water level to establish the height of each post. Fasten one end of the water level, so the water line is even with the bottom of the ledger (or level with whatever edge your plan prescribes). Hold the water level on each post and mark the post at the water line. Transfer the mark around the posts. Larry Johnston Make Cut Line Depending on your construction plan, you can mark the cut line for the posts by using the depth of either the joist or beam (or both). Starting at the line that is level with the bottom of the ledger, measure down the depth of the joist and mark this point. Larry Johnston Mark All Deck Posts Transfer the cut line to all the faces of the deck posts using a speed square and a carpenter's pencil. Make this line dark enough to see it when the sawdust flies. You will need to be able to see the line to keep the blade from wandering. Larry Johnston Cut Deck Posts Holding the weight of a circular saw at right angles to the post can prove cumbersome (and even dangerous), especially when standing on a ladder for a raised deck. A reciprocating saw will prove more accurate. Keep the shoe of the saw on the surface of the post, and make sure the blade cuts straight along the line.